The Digital flow water meter and Flow Rate Indicator Count Up / Count Down / Time Monitor, is equipped with an LCD screen and can record from 500-99500 liters and from 30 up to 720 days. The Digiflow 8000T works with two AAA alkaline batteries and has a 3/8″ NPT input-output. This digital water flow meter is the ideal tool for water filters and coolers, in order to monitor the condition of the filters, but also to quantify instantaneous and total flow rates (consumption). You can set your required Literage or Timeline and the Digiflow 8000T will count down until it reaches Zero Litres or Zero Days. Once the capacity settings are reached, the LCD screen will start flashing and an audible alert will be made.
- Digital display of liters of water remaining to change the filter.
- Indication of instantaneous and total water flow
- Automatically save operation data when the batteries are off
- Volume totalized up to 99,500 liters
- Flow rate display from 1.5 to 14.1 liter/min
- Operating Voltage : 3 DC Volts (2 x AAA Batteries)
- Operating Current : 1.0 mA (work), 0.05 mA (sleep)
- Automatic data is memorized when battery power is off
- Pressure: Max. 6.0 bar (85 psi)
- Connection: 3/8″ NPT Male or 3/8″ BSP Male (Not included)
Slide off the cover case of the battery room, and put it into 2 x AAA batteries. Then slide the cover case back.
SETTING CAPACITY AND TIMING
Keep pressing the display button, then press the reset button and release both of the buttons. The DigliFlow 8000T will go into the setting mode. The digit will flash to notify you that the setting procedure is on.
Press the display button to choose the capacity. The sequence is 0-100-200-300…9800-9900-OFF. Then press the reset button to save the capacity. Then go into the Timing setting. *The capacity mode will be disabled when you choose OFF.
Press the Display button to choose the Timing. The sequence is 0-30-60-90…690-720-OFF. Then press reset to save the Timing. The setting procedure is completed. *The capacity mode will be disabled when you choose OFF. **The setting procedure will be terminated, and go back to the original status if there is no input for 10 seconds.
The specification of the DigiFlow8000T connectors is 3/8″ MNPT female. You could use any 3/8″ MNPT male connectors.
The DigiFlow 8000T will be automatically on when there is any water flowing through the sensor. It will be automatically off when there is no water flowing for 10 seconds.
Press the display button to display the status of the three modes of the DigiFlow 8000T. Capacity mode: showing the capacity left. Timing mode; showing the timing left. Flow rate mode: showing the current flow rate. The sequence is Flow-rate – Timing Capacity…
Press the reset button to reset the setting and return to the last setting.
ALARM – Noticing Alarm
When Capacity is lower than 30 gallons or timing is lower than 7 days, the buzzer will beep once and the digit will beep once and the digit will flash to notify you that is time for changing the filter cartridge when there is any water flowing through DigiFlow 8000T or press the display button.
When Capacity reaches 0 gallons or Timing reaches 0 days, the buzzer will beep twice and the digit will flash to notify you that you should change the filter cartridge when there is any water flowing through Digiflow 8000T or press the display button.
Low Battery Power Alarm
When the battery power is lower than the normal working level, the buzzer will beep twice to notify that is time for changing the battery. The data will be kept in memory when the battery power is run out or the battery is removed.
- Most Commonly Asked Questions when buying Water Filters in Cyprus - February 20, 2023
- Can you drink tap water in Cyprus? - December 20, 2022
- 5 Easy Homemade Sodastream Recipes | Soda Syrups - March 11, 2021
There are no reviews yet.